Revolutions to Milliradians calculator

test long

How to use it?

To use the calculator, place your cursor in the desired unit field and write a number.The calculator will automatically convert your number and display the result in the other unit fields. If needed use the dot "." as the decimal separator.

Rounding: 
rev
mil

Revolutions to Milliradians formula

Milliradians to Revolutions formula

Revolutions
Revolutions

Counterclockwise rotations about the center point where a complete rotation is equal to 1 turn (revolution).

Source: Wikipedia

Milliradians
Milliradians

The PSO-1 reticle in a Dragunov sniper rifle has 10 horizontal lines with 1-mil spacing, which can be used to compensate for wind drift, impact correction or range estimation.

Source: Wikipedia


Revolutions to Milliradians Conversion Table

Below you can generate and download as CSV, Excel, PDF or print the Revolutions to Milliradians conversion table based on your needs.

Selected rounding: none (You can change it above in the dropdown)

From:
To:
Increment:
rev mil rev mil rev mil rev mil
1 6283.1853071796 26 163362.81798667 51 320442.45066616 76 477522.08334565
2 12566.370614359 27 169646.00329385 52 326725.63597334 77 483805.26865283
3 18849.555921539 28 175929.18860103 53 333008.82128052 78 490088.45396001
4 25132.741228718 29 182212.37390821 54 339292.0065877 79 496371.63926719
5 31415.926535898 30 188495.55921539 55 345575.19189488 80 502654.82457437
6 37699.111843078 31 194778.74452257 56 351858.37720206 81 508938.00988155
7 43982.297150257 32 201061.92982975 57 358141.56250924 82 515221.19518873
8 50265.482457437 33 207345.11513693 58 364424.74781642 83 521504.38049591
9 56548.667764616 34 213628.30044411 59 370707.9331236 84 527787.56580309
10 62831.853071796 35 219911.48575129 60 376991.11843078 85 534070.75111026
11 69115.038378975 36 226194.67105847 61 383274.30373795 86 540353.93641744
12 75398.223686155 37 232477.85636564 62 389557.48904513 87 546637.12172462
13 81681.408993335 38 238761.04167282 63 395840.67435231 88 552920.3070318
14 87964.594300514 39 245044.22698 64 402123.85965949 89 559203.49233898
15 94247.779607694 40 251327.41228718 65 408407.04496667 90 565486.67764616
16 100530.96491487 41 257610.59759436 66 414690.23027385 91 571769.86295334
17 106814.15022205 42 263893.78290154 67 420973.41558103 92 578053.04826052
18 113097.33552923 43 270176.96820872 68 427256.60088821 93 584336.2335677
19 119380.52083641 44 276460.1535159 69 433539.78619539 94 590619.41887488
20 125663.70614359 45 282743.33882308 70 439822.97150257 95 596902.60418206
21 131946.89145077 46 289026.52413026 71 446106.15680975 96 603185.78948924
22 138230.07675795 47 295309.70943744 72 452389.34211693 97 609468.97479642
23 144513.26206513 48 301592.89474462 73 458672.52742411 98 615752.1601036
24 150796.44737231 49 307876.0800518 74 464955.71273129 99 622035.34541078
25 157079.63267949 50 314159.26535898 75 471238.89803847 100 628318.53071796

  • Revolution (360°)
    A turn is a unit of plane angle measurement equal to 2π radians, 360 degrees or 400 gradians. A turn is also referred to as a cycle (abbreviated cyc), revolution (abbreviated rev), complete rotation (abbreviated rot) or full circle.
  • Milliradian (0.0563°)
    A milliradian, often called a mil or mrad, is an SI derived unit for angular measurement which is defined as a thousandth of a radian (0.001 radian). Mils are used in adjustment of firearm sights by adjusting the angle of the sight compared to the barrel (up, down, left or right). Mils are also used for comparing shot groupings, or to compare the difficulty of hitting different sized shooting targets at different distances. When using a scope with both mil adjustment and a reticle with mil markings (called a mil/mil scope), the shooter can use the reticle as a "ruler" to count the number of mils a shot was off target which directly translates to the sight adjustment needed to hit the target with a follow up shot. Optics with mil markings in the reticle can also be used to make a range estimation of a known size target, or vice versa to determine a target size if the distance is known, a practice called "milling".
Tags Revolutions to Milliradians rev to mil Revolutions rev Milliradians mil converter calculator conversion table